The micro-opening safety valve is a safety protection valve, and its opening and closing member is normally closed under the action of external force. When the pressure of the medium in the equipment or pipeline rises, it automatically opens when the value exceeds the specified value, and is discharged to the outside of the system. Media to prevent media pressure in pipes or equipment from exceeding specified values. Safety valves are automatic valves, mainly used in boilers, pressure vessels and pipelines. The control pressure does not exceed the specified value, which plays an important role in protecting personal safety and equipment operation. According to the safety valve flap opening height, it can be divided into micro-opening safety valve and full-opening safety valve. The opening stroke height of the micro-opening safety valve is: ≤0.05d0 (zui small discharge throat diameter); full-open safety valve The opening height is ≤ 0.25d0 (zui small discharge throat diameter). According to the structure form, it is divided into vertical hammer type, lever type, spring type and pilot type (pulse type); according to the valve body structure, it can be divided into closed type and non-closed type. Enclosed safety valves, ie, excluded media, are not leaked and are all discharged along the outlet to a designated location, typically used in toxic and corrosive media. For safety valves for air and steam, non-closed safety valves are often used. The selection of safety valve products should be determined according to the actual sealing pressure. For spring-loaded safety valves, springs with several working pressure levels within a nominal pressure (PN) range, in addition to the safety valve type, name, medium and temperature, the valve body sealing pressure should be noted. Otherwise, it is supplied according to the large sealing pressure of zui. The following should be noted for the installation and maintenance: All safety valves should be installed vertically. There should be no resistance at the exit of the safety valve to avoid pressure. The safety valve should be specially tested before installation and checked for its official seal. The safety valve in use should be inspected regularly. Safety valve installation should meet the following requirements: (l) For boilers with a rated evaporation of more than 0.5t/h, install at least two safety valves: boilers with a rated evaporation of less than or equal to 0.5t/h, with at least one safety valve. Dividable Safety valves must be installed at the exit of the economizer and at the outlet of the steam superheater. (2) The safety valve should be installed vertically in the high position of the boiler and the box. Between the safety valve and the drum or header, the outlet pipe and valve for steam should not be installed. (3) There must be a device for preventing the weight from moving by itself and a guide for restricting the deviance of the lever. The spring-type safety valve should have a device for lifting the handle and preventing the adjustment screw from being twisted. (4) For boilers with rated steam pressure less than or equal to 3.82 MPa, the safety valve throat diameter shall not be less than 25 mm: for boilers with rated steam pressure greater than 3.82 MPa, the safety valve throat diameter shall not be less than 20 mm. (5) The connecting pipe of the safety valve and the boiler shall have a sectional area not less than the inlet cross-sectional area of ​​the safety valve. If several safety valves are installed together on a short pipe directly connected to the drum, the cross-sectional area of ​​the short pipe should not be 1.25 times that of all safety valves. (6) Safety valves should generally be equipped with exhaust pipes. The exhaust pipes should be straight to a safe place and have sufficient cross-sectional area to ensure unobstructed exhaust. The bottom of the safety valve exhaust pipe should be filled with a drain pipe that is connected to a safe place, and no valve is allowed on the exhaust pipe and the drain pipe.
Honghui capsule produces gelatin hollow capsule in large scale with well-equipped facilities.
The
gelatin hollow capsule is a shell with special color and shape, made of
the main raw material of gelatin. It is always used as special
packaging of medicines or health care products which have bad smell,
light sensitive of unstable,.
The capsules do not
need adhesives and numerous excipients during the production process,
easy to disintegrate and release in gastric juice.
Empty Hard Gelatin Capsules,Empty Capsules Size 3,Empty Gelatin Capsules Size 3,Size 3 Gelatin Empty Capsules Zhejiang Honghui Capsule Co.,Ltd , https://www.hhcapsule.com