Pulverizer Material into the sealed bowl, bowl with hammer and broken ring, the motor drives the eccentric weight high-speed rotation, form vibration impact force and friction force, the material made into powder. Abrasive pot seal without sample loss and special wear-resistant materials. Long service life. Smooth running, low noise, small foot do not need to be fixed. The machine seal design so as to meet the requirements of environmental protection and safety production.This porduct can as lab pulverizer,lab ore pulverizer,too.
Model
FM-1
FM-2
FM-3
Mesh size of feed (mm)
<15
Mesh size of discharging(mesh)
80-200
Feed quantity(g)
<150
<300
<450
Power
380V 50HZ
Hardness of earthen bowl
HRC30-35
Impact value
J/cm²≥39.2
Wiring
Three-phase four-wire
Overall dimension(mm)
450*450*665
Motive power
Y90L-6
Weight of whole machine(kg)
120
124
130
Note:FM-1 is with 1 earthen bowl,FM-2 with 2 earthen bowls,FM-3 is with 3 earthen bowls
Packaging:
Factory photos:
Pulverizer Coal Pulverizer ,Concrete Pulverizer,Pulverizing Machine,Dirt Pulverizer,Lab Pulverizer,Lab ORE Pulverizer Cangzhou Blue Beauty Lab Instrument Co., Ltd. , https://www.czlabinstrument.com
Timely clearance of fruit surface fruit body cap diameter of 1 ~ 1.5 cm, stipe length 14 ~ 15 cm when the harvest, timely removal of the mushroom head and mushroom residue on the surface after harvest, remove the individual surface of the old bacteria compacted Silk, to minimize mechanical damage, protect the original mushroom base.
Appropriate ventilation and cooling In the mushrooming stage, in order to harvest high-quality velvet mushroom with small cover, long shank, light color, and rich tenderness, it is generally covered with a layer of plastic film on the bacterium bag to ensure the required humidity for the mushroom growth and create a carbon dioxide. High concentration of microenvironment. However, high humidity and high carbon dioxide concentration are not conducive to renewing budding. It can be used to remove air and ventilation in the morning and evening so that it can form the original foundation as quickly as possible and accelerate the tide.
The faintly scattered light mushroom can completely form mushroom primordium in the dark environment, but the amount formed is far less than that formed in the weak light scattering environment. Therefore, a certain amount of scattered light should be given during the tide transition. The "seventh-shade" environment can speed up the differentiation of the primordium of the mushroom to form a mushroom bud.
The most suitable temperature for the rational control of the temperature of the mushroom was 13°C～15°C. If the temperature is high, you can increase the amount of water spray in the empty room, and fully ventilate and cool. It should be noted that when the temperature is high, the humidity can not be too large, otherwise it will make the mushroom legs black and the villi increase, thus causing diseases. If the temperature is low, you can spray hot water or warm the mushroom room to avoid delaying the formation of mushroom primordium due to excessive temperature difference and affecting the growth of mushroom buds, which is not conducive to turning tides.
The water content of the culture material should be suitable for the moisture content of the culture material to reach 65% to 70% in order to ensure its normal growth and smooth transition in the later period. If the culture material is relatively dry, add more fresh water in the bag at one time, and pour excess water after 2 to 4 hours. Add 50 to 100 ml to each bag.
Mushrooming After the second tidal mushroom is picked, it should be turned on the other side to produce mushrooms, which will increase the speed of tidal turnover, and the yield is equivalent to that of the first tidal mushroom. However, it should be noted that the mycelium that is not thoroughly translucent or has bacterial infections should not be turned into a mushroom.
Prevent mushroom bulbs from surrounding bulbs often appear around the mushroom, there is no or little fruiting phenomenon in the middle, you can add 20% of the mixed material in the culture material, not only to prevent around the mushroom, but also promote the formation of mushroom primordium .
Seven points to speed up the turning of mushroom
Flammulina Turnover refers to the whole process from the end of tidal mushroom picking to the formation of the next tidal mushroom. The duration of the tidal time directly affects the total production of the mushroom. Here's how to speed up the migration of the mushroom: