BK7 or K9L domes are used primarily in meteorology applications. BK7 offers excellent transmission from 300nm up to 2µm. BK7 is a relatively hard material, with excellent chemical durability. Collimator Lens,Led Collimator Lens,Laser Collimator Lens,Optical Collimator Lens ChangChun Worldhawk Optics Co.,Ltd , https://www.worldhawk-optics.com
UV fused silica domes: For applications operating in the deeper UV range, Worldhawk offers a range of UV fused silica domes. Fused silica domes are commonly used in underwater applications at extremely high pressures.
Sapphire domes: For infrared applications we can provide sapphire domes. Sapphire is an extremely hard material with transmission of over 80% in the 2-5µm wavelength range. As with fused silica, sapphire is able to withstand extreme pressures, making it the perfect material for underwater camera and missile fairing applications.
Introduction of Cleaning Methods for Three Major Agricultural Machinery Parts
Agricultural machinery parts play an important role in the use and operation of the entire farm machinery. However, different cleaning methods should be adopted for agricultural machinery parts with different materials and precision. First, remove scale 1, with hydrochloric acid. When clearing the scale of cast iron cylinder block, etc., the concentration of 8% to 10% of hydrochloric acid and 3% of the hydrochloric acid equivalent of Ruo Ding corrosion inhibitor solution heated to 50 ~ 60 °C into the water jacket, immersion 2 ~ 3 hours Discharge, wash with an aqueous solution added with potassium dichromate, or use a 5% concentration of aqueous caustic soda solution to inject the water jacket and neutralize the residual acid solution. Then rinse with water several times until it is clean. This method is suitable for removing scales whose major components are calcium carbonate and calcium sulfate. 2. Use caustic soda solution. When removing silicate-based scale, add 2% to 3% of the caustic soda aqueous solution to the cooling system. Wait for 1 to 2 days after the standby vehicle runs. Rinse with clean water, repeat once, and finally use clean water. Clean the cooling system. Second, the removal of oil 1, with alkaline solution degreasing. For removal of animal and vegetable fats and mineral oils on the surface of steel parts, a small amount of emulsifier can be added to the alkaline solution and cleaned after warming. If pressure injection is used, the degreasing effect is better. After cleaning, spray with heated clean water to rinse off the alkali solution remaining on the surface of the part. 2, degreasing with organic solvents. In order to prevent the strong corrosion of alkaline solutions to precision parts (such as high-pressure pumps, fuel injectors, etc.), organic solvents such as gasoline, kerosene, diesel oil, and alcohol are generally used. Such parts are cleaned, and heating is generally not required. 3, with aluminum alloy cleaning fluid degreasing. Since the alkali solution has a strong corrosion effect on the aluminum alloy and the organic solvent is expensive, when an aluminum alloy part is required to be repaired, the aluminum alloy cleaning solution can be configured to be cleaned. Usually use sodium silicate or sodium carbonate solution plus a small amount of potassium dichromate to prepare, heating to 60 ~ 70 °C for optimal cleaning results. Third, remove coke 1, mechanical method can generally be used metal brush, blade and broken piston rings and other eradication of carbon deposition. However, because this method is easy to scratch the surface of parts, it is not necessary to use abrasive cloth and steel spatula to remove coke on the precision parts. It can be removed with wood, bamboo or copper spatula, or it can be rubbed back and forth on the cork board. . After removing the coke from the part mechanically, it must be carefully cleaned with oil. This method is simple and does not require equipment, but the disadvantage is that the hard-to-reach parts of the carbon deposit are not easy to clean. 2. The chemical method places parts in a prepared chemical solution, soaks for a period of time to soften the coke, and then removes the parts, removes the charcoal with a brush or a cotton wire, and cleans it with hot water. It's dry.