Impact Drill Impact Drill,Impact Cordless Drill,Electric Impact Drill,Corded Impact Drill ZHE JIANG ULITE TOOLS MANUFACTURE CO.,LTD , http://www.ulitepowertool.com
December pollution-free vegetable production calendar
The seedlings are watered the day before seedling splitting, and the amount of water should be less. Use a shovel to raise the seedlings. Use seedlings that are robust, uniform in size, and free of pests. According to the 8 cm line spacing, open a shallow ditch, from the ground level, about 5 cm deep, the ditch should be straight, the outer ditch should be steep, and the ditch should be flat. Use a water bottle to water in the ditch, and then place the seedlings in the ditch at a spacing of 8 cm. The seedlings should cling to the lateral ditch. The seedlings should be straightened and the roots should be stretched. When there is water in the ditch, return all the soil that was ploughed out during the ditching, keep the seedbed flat, and be wet and dry on top, and loosen the topsoil. Using earth seedlings, put the selected seedlings into the holes in the earth’s center and pay attention to the extension of the roots. Fill the holes with warm fines and slightly higher. If the Turkish side is doing a good job in advance, it must be watered to dig the earth before it is divided. Use nutritious paper bags (钵) to divide the seedlings, first plant the seedlings inside, and then water. Increase seed bed temperature after seedlings, 25-28 °C during the day and 15-20 °C in the evening. After easing the seedlings, gradually ventilate and lower the temperature of the seedbeds, and control them at 20-25°C during the day and 10-15°C at night. Maintain soil moisture after seedling and reduce air humidity. If the soil in the midway seedlings is dry and the growth of the seedlings is hindered, a water can be poured on the sunny morning, and the amount of water should be small. After watering, pay attention to warming and air release to reduce the air humidity. Timely soil, depth of about 2 cm. The use of nutritional paper bags, or nutrition, or soil nutrition sub-seedlings, pay attention to nutrient soil after sub-seedling can not be too dehydration drought, see the dry immediately spray, plastic nutrients can be watered in the pot, through all the nutrients. Watering should take place on a sunny morning. After the water is sprayed, it should be warmed and ventilated. After seedling, attention should be paid to improving seedbed conditions. If late blight and gray mold occur after seedling separation, remove the diseased plants, remove the leaves of gray mold, burn them or bury them deeply, and immediately spray and control them; the main insect pests are vegetables and aphids. Check at any time and spray pesticides in a timely manner. The use of nutritious earthenware, nutritional paper bags (or nutrients) seedlings in order to make the seedlings grow robust and tidy. The seedlings can be moved to the stove, the flue, and exchanged with the big seedlings. From sub-seedling to planting, it is usually 1-2 times, and should be handled lightly, placed neatly, filled with smashed dirt at the gap between the days, around the soil, in order to maintain the moisture within the earth.
ULITE Impact Drill have high power. 500W, 530W ,800W. Long longevity motor using. Quiet and smooth gear voice. Little sparkling. Variable speed and reversing switch. Bearing is C & U certificated in china. Using longevity is long. Worker using is high efficiency. Drill chuck is 13mm.
Safety
1. Be sure to carry out strictly the relevant rules or obey the explanation first.
2. The workpiece to be drilled must be paied more attention regulary when it is drilled.
3. Use the plug correctly. Don`t change the plug and wire separately. And don`t access to power if the plug wire is broken. Take off the plug in time when the electric drill isn`t used.
4. Don`t extend the length of the power wire, and keep the power wire away from the heat source and oil.
Operation
1. Pls use machine under accurate voltage.
2. Keep the tool in non-loading for one minute. Check the transmission position is flexible and make sure there is no abnormal. Check the inverting switch is normal.
3. The head of the drill is sharp, Pls don`t touch is when you are drilling. If the rotation speed is reduced abnormally or stop suddenly or get stuck. Please turn off the power immediately.
4. Carbon brush should be checked periodically and replaced in time. If the carbon brush is finished, the carbon brush end would contact with commutator. The motor would be burnt.
5. When it is in following conditions, Pls don`t be used and send to repair immediately.
a. The insulation is damaged.
b. The power wire or electric cable case is broken.
c. The plug and wire is broken.
d. The sparkle appears seriously
6. The tools must be grounded and avoid to be shocked.